EL-UB0AJI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EL-UB0AJI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Value1*	Value2*	Value3*	Value4*
1789965253	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1789964653	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1789964053	0 RX Erlang	0 TX Erlang	1 RXcount/10m	0 TXcount/10m
1789963453	0 RX Erlang	0.01 TX Erlang	1 RXcount/10m	1 TXcount/10m
1789962853	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1789962253	0 RX Erlang	0.02 TX Erlang	0 RXcount/10m	2 TXcount/10m
1789961653	0 RX Erlang	0.01 TX Erlang	2 RXcount/10m	1 TXcount/10m
1789961053	0.01 RX Erlang	0 TX Erlang	2 RXcount/10m	0 TXcount/10m
1789960453	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1789959853	0 RX Erlang	0.01 TX Erlang	0 RXcount/10m	1 TXcount/10m
1789959253	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1789958653	0 RX Erlang	0 TX Erlang	0 RXcount/10m	0 TXcount/10m
1789958053	0 RX Erlang	0 TX Erlang	1 RXcount/10m	0 TXcount/10m
1789957453	0.01 RX Erlang	0 TX Erlang	4 RXcount/10m	0 TXcount/10m

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)