SP9MOA-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9MOA-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Tx1h*
1787563707	13.9 Volt	490 Pkt	40 Pkt
1787562506	13.68 Volt	390 Pkt	40 Pkt
1787560103	13.9 Volt	310 Pkt	20 Pkt
1787558902	13.83 Volt	310 Pkt	10 Pkt
1787557702	13.75 Volt	270 Pkt	10 Pkt
1787556500	13.75 Volt	270 Pkt	20 Pkt
1787555299	13.75 Volt	330 Pkt	50 Pkt
1787554098	13.68 Volt	380 Pkt	70 Pkt
1787552899	13.38 Volt	360 Pkt	60 Pkt
1787551696	13 Volt	310 Pkt	40 Pkt
1787550494	12.93 Volt	280 Pkt	20 Pkt
1787549293	12.78 Volt	330 Pkt	20 Pkt
1787548092	12.78 Volt	340 Pkt	20 Pkt
1787546891	12.7 Volt	380 Pkt	30 Pkt
1787545690	12.7 Volt	370 Pkt	30 Pkt
1787544489	12.7 Volt	390 Pkt	30 Pkt
1787543287	12.7 Volt	380 Pkt	10 Pkt
1787542198	12.7 Volt	390 Pkt	10 Pkt
1787540885	12.7 Volt	380 Pkt	10 Pkt
1787539684	12.7 Volt	400 Pkt	10 Pkt
1787538483	12.7 Volt	370 Pkt	20 Pkt
1787537282	12.78 Volt	370 Pkt	20 Pkt
1787536080	12.78 Volt	350 Pkt	20 Pkt
1787534880	12.78 Volt	350 Pkt	20 Pkt
1787533678	12.78 Volt	370 Pkt	20 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, -0.2

Rx1h: 0, 10, 0

Tx1h: 0, 10, 0

None: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)