KQ6DI-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KQ6DI-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	18B20*	CPU*	pTemp*	Press*	Alt*
1789944633	74.3	39.2	72.8	1010.7	70
1789944335	74.2	39.2	72.7	1010.7	70
1789944035	74	38.6	72.6	1010.8	67
1789943735	73.7	38.6	72.3	1010.9	62
1789943435	73.4	38.6	71.8	1010.9	65
1789943134	73	37	71.2	1011	63
1789942835	72.4	34.3	70.5	1010.9	65
1789942535	73.4	34.9	71.5	1011.1	62
1789942235	74.4	38.1	73.2	1011.2	56
1789941935	74.3	39.2	73.1	1011.2	55
1789941635	74.3	39.7	73.1	1011.2	58
1789941335	74.2	38.6	73	1011.2	56
1789941034	74.2	38.6	72.8	1011.3	54
1789940735	74.1	38.6	72.8	1011.3	54
1789940435	74	39.2	72.7	1011.3	53
1789940135	74	39.2	72.7	1011.4	51
1789939835	73.8	38.6	72.6	1011.5	49
1789939534	73.8	38.6	72.6	1011.5	49
1789939235	73.7	39.2	72.5	1011.5	47
1789938935	73.6	38.6	72.5	1011.6	47
1789938635	73.6	39.2	72.4	1011.5	48
1789938335	73.5	38.6	72.3	1011.4	52
1789938035	73.4	38.6	72.3	1011.4	53
1789937735	73.4	38.6	72.2	1011.4	51
1789937433	73.3	38.6	72.1	1011.7	44

*Used Equation Coefficients:

18B20: 0, 0.1, 0

CPU: 0, 0.1, 0

pTemp: 0, 0.1, 0

Press: 0, 0.1, 700

Alt: 0, 1, -1000

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)