ED1ZAP-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED1ZAP-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	V.BAT*	C.LOAD*	TEMP*	V.PLS*
1788662041	12.5 V	1.53 A	25.5 C	5 V
1788661140	12.5 V	1.61 A	25.5 C	5 V
1788660239	12.5 V	1.45 A	25.5 C	5 V
1788659338	12.5 V	1.85 A	26 C	5 V
1788658438	12.5 V	1.53 A	26 C	5 V
1788656636	12.5 V	1.45 A	26 C	5 V
1788655735	12.5 V	1.85 A	26.5 C	5 V
1788654834	12.6 V	1.53 A	26.5 C	5 V
1788653933	12.6 V	1.61 A	26.5 C	5 V
1788653032	12.6 V	2.42 A	27 C	5 V
1788652132	12.6 V	1.77 A	27 C	5 V
1788651231	12.6 V	1.53 A	27 C	5 V
1788650330	12.6 V	1.77 A	27.5 C	5 V
1788649429	12.6 V	1.61 A	27.5 C	5 V
1788648528	12.6 V	1.93 A	27.5 C	5 V
1788647628	12.6 V	1.61 A	28 C	5 V
1788646726	12.6 V	1.69 A	28 C	5 V
1788645825	12.6 V	1.61 A	28.5 C	5 V
1788644945	12.6 V	1.85 A	28.5 C	5 V
1788644024	12.7 V	1.69 A	28.5 C	5 V
1788643123	12.7 V	1.77 A	29 C	5 V
1788642222	12.7 V	1.61 A	29 C	5 V
1788641322	12.7 V	1.85 A	29.5 C	5 V
1788640420	12.7 V	1.53 A	29.5 C	5 V
1788639519	12.7 V	2.66 A	29.5 C	5 V

*Used Equation Coefficients:

V.BAT: 0, 0.1, 0

C.BAT: 0, 0.0806, 0

C.LOAD: 0, 0.0806, 0

TEMP: 0, 0.5, -64

V.PLS: 0, 0.2, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)