W1DMR-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W1DMR-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773270606	13.95 Volt	1290 Pkt	80 Pcnt
1773270306	13.95 Volt	1300 Pkt	79 Pcnt
1773270006	13.95 Volt	1310 Pkt	79 Pcnt
1773269705	13.95 Volt	1310 Pkt	78 Pcnt
1773269406	13.95 Volt	1330 Pkt	78 Pcnt
1773269106	13.95 Volt	1320 Pkt	78 Pcnt
1773268806	13.95 Volt	1300 Pkt	78 Pcnt
1773268506	13.95 Volt	1300 Pkt	78 Pcnt
1773268206	13.95 Volt	1290 Pkt	77 Pcnt
1773267906	13.95 Volt	1310 Pkt	77 Pcnt
1773267606	13.95 Volt	1290 Pkt	77 Pcnt
1773267306	13.95 Volt	1290 Pkt	77 Pcnt
1773267006	13.95 Volt	1280 Pkt	77 Pcnt
1773266706	13.95 Volt	1210 Pkt	76 Pcnt
1773266406	13.95 Volt	1210 Pkt	77 Pcnt
1773266106	13.95 Volt	1210 Pkt	77 Pcnt
1773265806	13.95 Volt	1190 Pkt	76 Pcnt
1773265506	13.95 Volt	1180 Pkt	76 Pcnt
1773265206	13.95 Volt	1170 Pkt	76 Pcnt
1773264906	13.95 Volt	1160 Pkt	77 Pcnt
1773264606	13.95 Volt	1160 Pkt	77 Pcnt
1773264306	13.95 Volt	1150 Pkt	76 Pcnt
1773264006	13.95 Volt	1160 Pkt	76 Pcnt
1773263706	13.95 Volt	1140 Pkt	76 Pcnt
1773263406	13.95 Volt	1140 Pkt	75 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)