BI1NPE-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BI1NPE-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TEMP*	HUM*	BARO*
1780887567	26.96 C	39.85 %HR	828 hPa
1780887507	27.06 C	39.42 %HR	828 hPa
1780887447	27.13 C	38.78 %HR	828 hPa
1780887387	27.19 C	38.88 %HR	828 hPa
1780887327	27.21 C	38.7 %HR	828 hPa
1780887267	27.27 C	38.68 %HR	828 hPa
1780887207	27.35 C	38.61 %HR	828 hPa
1780887147	27.45 C	38.27 %HR	828 hPa
1780887087	27.54 C	38.3 %HR	828 hPa
1780887027	27.62 C	38.3 %HR	828 hPa
1780886970	27.79 C	38.26 %HR	828 hPa
1780886907	28.02 C	38.39 %HR	828 hPa
1780886847	28.42 C	38.12 %HR	828 hPa
1780886787	29.04 C	37.9 %HR	828 hPa
1780886727	29.76 C	36.67 %HR	828 hPa
1780886669	28.45 C	51.28 %HR	828 hPa
1780886607	27.79 C	38.8 %HR	828 hPa
1780886547	27.84 C	39.16 %HR	828 hPa
1780886487	27.92 C	39.71 %HR	828 hPa
1780886427	28.01 C	40.05 %HR	828 hPa
1780886367	28.05 C	40.21 %HR	828 hPa
1780886307	28.11 C	40.69 %HR	828 hPa
1780886247	28.14 C	40.68 %HR	828 hPa
1780886187	28.22 C	40.91 %HR	828 hPa
1780886127	28.31 C	41.12 %HR	828 hPa

*Used Equation Coefficients:

TEMP: 0, 0.01, 0

HUM: 0, 0.01, 0

BARO: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)