DG7RJ-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG7RJ-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1788614163	25.5 C deg	51.1 %	0 C deg
1788612345	25.4 C deg	51 %	0 C deg
1788610535	25.3 C deg	51 %	0 C deg
1788608716	25.2 C deg	51 %	0 C deg
1788606898	25.1 C deg	51.3 %	0 C deg
1788605093	25 C deg	51.5 %	0 C deg
1788603269	24.9 C deg	51.8 %	0 C deg
1788601452	24.9 C deg	51.8 %	0 C deg
1788599637	25 C deg	51.9 %	0 C deg
1788597824	24.1 C deg	57.3 %	0 C deg
1788596942	24.6 C deg	51.5 %	0 C deg
1788595127	24.8 C deg	51.2 %	0 C deg
1788593309	24.9 C deg	51 %	0 C deg
1788591493	25 C deg	50.8 %	0 C deg
1788589682	25.2 C deg	50.7 %	0 C deg
1788587869	25.3 C deg	50.6 %	0 C deg
1788586049	25.5 C deg	50.3 %	0 C deg
1788584233	25.7 C deg	49.8 %	0 C deg
1788582422	25.9 C deg	49.8 %	0 C deg
1788580606	26 C deg	49.6 %	0 C deg
1788578791	26.1 C deg	49.8 %	0 C deg
1788576973	26.3 C deg	49.8 %	0 C deg
1788575159	26.4 C deg	49.8 %	0 C deg
1788573346	26.6 C deg	49.5 %	0 C deg
1788569716	26.9 C deg	48.9 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)