DO9HM-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DO9HM-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1776630683	7 deg C	76.7 %	1019.7 hPa
1776629783	7 deg C	76.4 %	1019.8 hPa
1776628880	7 deg C	76.2 %	1019.9 hPa
1776627977	7.1 deg C	75.9 %	1020 hPa
1776627082	7 deg C	75.9 %	1020.2 hPa
1776626180	6.7 deg C	76 %	1020.1 hPa
1776625277	6.2 deg C	75.9 %	1020.1 hPa
1776624373	6.2 deg C	74.5 %	1020.1 hPa
1776623476	6.7 deg C	73.6 %	1019.8 hPa
1776622571	7.2 deg C	72.5 %	1019.5 hPa
1776606372	13.8 deg C	59.7 %	1016 hPa
1776605468	15.1 deg C	58 %	1015.7 hPa
1776604573	15 deg C	58 %	1016 hPa
1776603677	14.8 deg C	61 %	1016 hPa
1776602776	14.1 deg C	63 %	1016.2 hPa
1776601874	14.8 deg C	60.9 %	1016 hPa
1776600978	14.6 deg C	60.9 %	1016 hPa
1776600074	15.6 deg C	62.4 %	1016 hPa
1776599179	14.6 deg C	64.3 %	1015.9 hPa
1776598281	14.5 deg C	65.1 %	1015.9 hPa
1776597376	15 deg C	65 %	1015.6 hPa
1776596472	14.6 deg C	67.5 %	1015.5 hPa
1776595574	15.3 deg C	69.2 %	1015.1 hPa
1776594670	12.3 deg C	77.8 %	1015.8 hPa
1776593770	12 deg C	76.5 %	1016 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)