DC1MPP-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC1MPP-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1788563805	25.8 deg C	46.1 %	1014.6 hPa
1788562909	25.8 deg C	46 %	1014.5 hPa
1788562011	25.8 deg C	45.8 %	1014.5 hPa
1788561109	25.8 deg C	45.7 %	1014.4 hPa
1788560211	25.8 deg C	45.5 %	1014.3 hPa
1788559307	25.9 deg C	45.4 %	1014.2 hPa
1788558407	25.9 deg C	45.2 %	1014.1 hPa
1788557510	25.9 deg C	45.1 %	1013.9 hPa
1788556627	25.9 deg C	45 %	1013.9 hPa
1788555703	25.9 deg C	44.8 %	1013.9 hPa
1788554803	25.9 deg C	44.7 %	1013.9 hPa
1788553906	26 deg C	44.5 %	1013.9 hPa
1788553007	26 deg C	44.4 %	1013.8 hPa
1788552106	26 deg C	44.3 %	1013.7 hPa
1788551203	26.1 deg C	44.2 %	1013.7 hPa
1788550300	26.1 deg C	44.1 %	1013.6 hPa
1788549402	26.1 deg C	44 %	1013.5 hPa
1788548498	26.2 deg C	43.8 %	1013.4 hPa
1788547601	26.2 deg C	43.7 %	1013.3 hPa
1788546698	26.3 deg C	43.5 %	1013.2 hPa
1788545794	26.4 deg C	43.2 %	1013 hPa
1788544895	26.4 deg C	43 %	1012.8 hPa
1788544056	26.5 deg C	42.7 %	1012.6 hPa
1788543151	26.6 deg C	42.4 %	1012.4 hPa
1788542249	26.7 deg C	42.1 %	1012.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)