OE6VAG Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE6VAG. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1788696091	12.53 Volt	100 Pcnt	23 C
1788694289	12.53 Volt	100 Pcnt	23 C
1788692489	12.53 Volt	100 Pcnt	23 C
1788690689	12.53 Volt	100 Pcnt	23 C
1788688889	12.53 Volt	100 Pcnt	23 C
1788687089	12.53 Volt	100 Pcnt	23 C
1788685289	12.53 Volt	100 Pcnt	23 C
1788683489	12.53 Volt	100 Pcnt	23 C
1788681689	12.53 Volt	100 Pcnt	23 C
1788679889	12.53 Volt	100 Pcnt	23 C
1788678089	12.53 Volt	100 Pcnt	23 C
1788676290	12.53 Volt	100 Pcnt	23.5 C
1788674490	12.53 Volt	100 Pcnt	23 C
1788672690	12.53 Volt	100 Pcnt	23 C
1788670890	12.53 Volt	100 Pcnt	23 C
1788669090	12.53 Volt	100 Pcnt	23 C
1788667290	12.53 Volt	100 Pcnt	23 C
1788665490	12.53 Volt	100 Pcnt	23.5 C
1788663690	12.53 Volt	100 Pcnt	23.5 C
1788661890	12.53 Volt	100 Pcnt	23 C
1788660090	12.53 Volt	100 Pcnt	23 C
1788658290	12.53 Volt	100 Pcnt	23 C
1788656490	12.53 Volt	100 Pcnt	23 C
1788654690	12.53 Volt	100 Pcnt	23 C
1788652890	12.53 Volt	100 Pcnt	23 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)