DL6DBZ-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL6DBZ-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Celsius*	Rel_Hum*	Atm_Press*	GAS*
1787545100	24.4 C	42.85 %	1024 hPa	0.96 %
1787543581	25.9 C	43.22 %	0 hPa	0 %
1787459388	26.2 C	43.07 %	0 hPa	0 %
1787459321	26.2 C	43.05 %	0 hPa	0 %
1787459268	26.2 C	43.01 %	0 hPa	0 %
1787458853	26.3 C	43.04 %	0 hPa	0 %
1787442883	27.3 C	42.72 %	0 hPa	0 %
1787442420	27.3 C	42.7 %	0 hPa	0 %
1787442162	27.3 C	42.74 %	0 hPa	0 %
1787442140	27.3 C	42.74 %	0 hPa	0 %
1787442094	27.3 C	42.74 %	0 hPa	0 %
1787442037	27.3 C	42.74 %	0 hPa	0 %
1787441994	27.3 C	42.74 %	0 hPa	0 %
1787441931	27.3 C	42.73 %	0 hPa	0 %
1787441296	27.4 C	42.71 %	0 hPa	0 %
1787440959	27.4 C	42.75 %	0 hPa	0 %
1787440874	27.4 C	42.73 %	0 hPa	0 %
1787440848	27.4 C	42.72 %	0 hPa	0 %
1787440831	27.4 C	42.72 %	0 hPa	0 %
1787440300	27.4 C	42.74 %	0 hPa	0 %
1787440277	27.4 C	42.74 %	0 hPa	0 %
1787439607	27.5 C	42.77 %	0 hPa	0 %
1787439545	27.5 C	42.77 %	0 hPa	0 %
1787439528	27.5 C	42.77 %	0 hPa	0 %
1787439458	27.5 C	42.77 %	0 hPa	0 %

*Used Equation Coefficients:

Celsius: 0, 0.1, -50

Rel_Hum: 0, 0.01, 0

Atm_Press: 0, 0.125, 0

GAS: 0, 0.01, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)