AE6DC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AE6DC-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1784696194	14.55 Volt	100 Pcnt	86.9 F
1784695294	14.55 Volt	100 Pcnt	86.9 F
1784694394	14.55 Volt	100 Pcnt	87.8 F
1784693494	14.55 Volt	100 Pcnt	87.8 F
1784692594	14.55 Volt	100 Pcnt	87.8 F
1784691694	14.55 Volt	100 Pcnt	87.8 F
1784690794	14.55 Volt	100 Pcnt	87.8 F
1784689894	14.55 Volt	100 Pcnt	87.8 F
1784688994	14.55 Volt	100 Pcnt	87.8 F
1784688094	14.55 Volt	100 Pcnt	87.8 F
1784687194	14.55 Volt	100 Pcnt	87.8 F
1784686295	14.55 Volt	100 Pcnt	87.8 F
1784685395	14.55 Volt	100 Pcnt	86.9 F
1784684495	14.55 Volt	100 Pcnt	86.9 F
1784683595	14.55 Volt	100 Pcnt	86.9 F
1784682701	14.55 Volt	100 Pcnt	86.9 F
1784681795	14.55 Volt	100 Pcnt	86 F
1784680895	14.55 Volt	100 Pcnt	86 F
1784679995	14.55 Volt	100 Pcnt	86 F
1784679095	14.55 Volt	100 Pcnt	86 F
1784678195	14.55 Volt	100 Pcnt	86 F
1784677295	14.55 Volt	100 Pcnt	86 F
1784676395	14.55 Volt	100 Pcnt	86 F
1784675495	14.55 Volt	100 Pcnt	86 F
1784674595	14.55 Volt	100 Pcnt	86 F

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.9, -83.2

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)