IZ8QHW-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IZ8QHW-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1772543546	12.23 Volt	10 Pkt	58 Pcnt
1772543545	12.23 Volt	10 Pkt	58 Pcnt
1772543245	12.23 Volt	10 Pkt	63 Pcnt
1772542946	12.23 Volt	10 Pkt	64 Pcnt
1772542945	12.23 Volt	10 Pkt	64 Pcnt
1772542645	12.23 Volt	20 Pkt	71 Pcnt
1772542346	12.23 Volt	10 Pkt	72 Pcnt
1772542345	12.23 Volt	10 Pkt	72 Pcnt
1772542045	12.23 Volt	20 Pkt	74 Pcnt
1772541746	12.23 Volt	20 Pkt	83 Pcnt
1772541445	12.23 Volt	20 Pkt	84 Pcnt
1772540845	12.23 Volt	20 Pkt	78 Pcnt
1772540545	12.23 Volt	10 Pkt	69 Pcnt
1772540245	12.23 Volt	20 Pkt	72 Pcnt
1772539946	12.23 Volt	10 Pkt	76 Pcnt
1772539945	12.23 Volt	10 Pkt	76 Pcnt
1772539645	12.23 Volt	20 Pkt	74 Pcnt
1772539346	12.23 Volt	10 Pkt	75 Pcnt
1772539346	12.23 Volt	10 Pkt	75 Pcnt
1772539045	12.23 Volt	10 Pkt	69 Pcnt
1772538746	12.23 Volt	10 Pkt	66 Pcnt
1772538745	12.23 Volt	10 Pkt	66 Pcnt
1772538445	12.23 Volt	10 Pkt	69 Pcnt
1772538146	12.23 Volt	10 Pkt	66 Pcnt
1772538145	12.23 Volt	10 Pkt	66 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)