BM6HFL-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HFL-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1753495180	31.5 C	7 p	20 p	739 p
1753493980	31.9 C	6 p	20 p	735 p
1753492780	31.7 C	7 p	25 p	733 p
1753491580	32 C	7 p	25 p	730 p
1753490380	31.1 C	11 p	25 p	727 p
1753489180	31.2 C	7 p	21 p	722 p
1753487980	31.4 C	7 p	23 p	719 p
1753486780	30.6 C	7 p	23 p	716 p
1753485580	30.8 C	9 p	23 p	713 p
1753484380	31 C	7 p	23 p	708 p
1753483181	30 C	7 p	23 p	705 p
1753481980	30.9 C	9 p	22 p	701 p
1753480780	30.8 C	7 p	20 p	697 p
1753479580	29.3 C	6 p	20 p	694 p
1753478380	27.9 C	7 p	20 p	693 p
1753477180	28.2 C	7 p	20 p	695 p
1753475980	28.7 C	6 p	20 p	696 p
1753474780	27.9 C	7 p	20 p	695 p
1753473580	28.6 C	7 p	20 p	693 p
1753472380	28.6 C	6 p	19 p	690 p
1753471180	27.7 C	7 p	21 p	687 p
1753469980	27.6 C	6 p	21 p	685 p
1753468780	28.8 C	8 p	22 p	685 p
1753467580	28.6 C	7 p	21 p	688 p
1753466380	29.1 C	7 p	23 p	690 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)