NE1CU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object NE1CU-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Rx1h*	Dg1h*
1776872837	12.3 Volt	70.4 DegF	0 Pkt	0 Pkt
1776871937	12.3 Volt	71.3 DegF	0 Pkt	0 Pkt
1776871037	12.3 Volt	71.3 DegF	0 Pkt	0 Pkt
1776870137	12.38 Volt	71.3 DegF	0 Pkt	0 Pkt
1776869237	12.38 Volt	72.2 DegF	0 Pkt	0 Pkt
1776868337	12.38 Volt	70.4 DegF	0 Pkt	0 Pkt
1776867437	12.38 Volt	69.5 DegF	0 Pkt	0 Pkt
1776866537	12.45 Volt	69.5 DegF	0 Pkt	0 Pkt
1776865637	12.45 Volt	70.4 DegF	0 Pkt	0 Pkt
1776864737	12.45 Volt	71.3 DegF	0 Pkt	0 Pkt
1776863837	12.45 Volt	72.2 DegF	0 Pkt	0 Pkt
1776862937	12.53 Volt	74 DegF	0 Pkt	0 Pkt
1776862037	12.53 Volt	73.1 DegF	0 Pkt	0 Pkt
1776861137	12.6 Volt	71.3 DegF	40 Pkt	10 Pkt
1776860237	12.6 Volt	69.5 DegF	150 Pkt	50 Pkt
1776859337	12.68 Volt	67.7 DegF	240 Pkt	80 Pkt
1776858437	12.75 Volt	64.1 DegF	350 Pkt	120 Pkt
1776857537	12.83 Volt	62.3 DegF	420 Pkt	150 Pkt
1776856637	12.75 Volt	62.3 DegF	400 Pkt	150 Pkt
1776855737	12.75 Volt	62.3 DegF	400 Pkt	150 Pkt
1776854847	12.75 Volt	62.3 DegF	360 Pkt	140 Pkt
1776853937	12.75 Volt	62.3 DegF	360 Pkt	130 Pkt
1776853037	13.43 Volt	62.3 DegF	370 Pkt	120 Pkt
1776852137	12.83 Volt	62.3 DegF	360 Pkt	130 Pkt
1776851237	12.98 Volt	62.3 DegF	370 Pkt	130 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.9, -97

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)