KC0CAP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC0CAP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Dg1h*	Eff1h*
1788685855	1520 Pkt	70 Pkt	61 Pcnt
1788685556	1510 Pkt	70 Pkt	61 Pcnt
1788685555	1510 Pkt	70 Pkt	61 Pcnt
1788685255	1510 Pkt	70 Pkt	60 Pcnt
1788684956	1530 Pkt	80 Pkt	61 Pcnt
1788684955	1530 Pkt	80 Pkt	61 Pcnt
1788684655	1540 Pkt	80 Pkt	61 Pcnt
1788684356	1540 Pkt	70 Pkt	62 Pcnt
1788684355	1540 Pkt	70 Pkt	62 Pcnt
1788684055	1530 Pkt	80 Pkt	62 Pcnt
1788683756	1530 Pkt	80 Pkt	61 Pcnt
1788683755	1530 Pkt	80 Pkt	61 Pcnt
1788683455	1510 Pkt	80 Pkt	62 Pcnt
1788683157	1520 Pkt	80 Pkt	61 Pcnt
1788683155	1520 Pkt	80 Pkt	61 Pcnt
1788682855	1510 Pkt	80 Pkt	61 Pcnt
1788682558	1500 Pkt	80 Pkt	60 Pcnt
1788682555	1500 Pkt	80 Pkt	60 Pcnt
1788682255	1520 Pkt	80 Pkt	60 Pcnt
1788681956	1520 Pkt	70 Pkt	60 Pcnt
1788681955	1520 Pkt	70 Pkt	60 Pcnt
1788681655	1520 Pkt	70 Pkt	61 Pcnt
1788681356	1520 Pkt	70 Pkt	60 Pcnt
1788681355	1520 Pkt	70 Pkt	60 Pcnt
1788681055	1510 Pkt	70 Pkt	60 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)