BV2FP-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2FP-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1781861494	30.4 C	5 p	5 p	33 p	505 p
1781860293	30.8 C	5 p	5 p	33 p	505 p
1781859093	30.4 C	5 p	5 p	33 p	505 p
1781857893	31 C	5 p	5 p	33 p	505 p
1781856694	29.6 C	5 p	5 p	33 p	505 p
1781855493	30.2 C	5 p	5 p	33 p	505 p
1781854294	30.9 C	5 p	5 p	33 p	505 p
1781853094	31.1 C	5 p	5 p	33 p	505 p
1781851895	31.5 C	5 p	5 p	33 p	505 p
1781850693	29.6 C	5 p	5 p	33 p	505 p
1781849493	30.3 C	5 p	5 p	33 p	505 p
1781848293	29.3 C	5 p	5 p	33 p	505 p
1781847094	31.4 C	5 p	5 p	33 p	505 p
1781845894	30.2 C	19 p	27 p	28 p	500 p
1781844693	30.4 C	19 p	27 p	28 p	500 p
1781843493	30.8 C	19 p	27 p	28 p	500 p
1781842294	31.5 C	19 p	27 p	28 p	500 p
1781841095	31.2 C	19 p	27 p	28 p	500 p
1781839893	29.8 C	19 p	27 p	28 p	500 p
1781838693	31.4 C	19 p	27 p	28 p	500 p
1781837493	29.2 C	19 p	27 p	28 p	500 p
1781836293	30.8 C	19 p	27 p	28 p	500 p
1781835094	30.3 C	19 p	27 p	28 p	500 p
1781833894	31.9 C	19 p	27 p	28 p	500 p
1781832694	29.7 C	19 p	27 p	28 p	500 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)