VE3XII-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VE3XII-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1757600759	12.3 Volt	670 Pkt	690 Pcnt
1757599487	12.3 Volt	580 Pkt	670 Pcnt
1757598227	12.3 Volt	470 Pkt	630 Pcnt
1757596967	12.3 Volt	430 Pkt	600 Pcnt
1757595707	12.3 Volt	450 Pkt	630 Pcnt
1757594447	12.3 Volt	460 Pkt	620 Pcnt
1757593187	12.3 Volt	450 Pkt	600 Pcnt
1757591927	12.3 Volt	460 Pkt	590 Pcnt
1757590667	12.3 Volt	490 Pkt	620 Pcnt
1757589407	12.3 Volt	610 Pkt	720 Pcnt
1757588147	12.3 Volt	640 Pkt	790 Pcnt
1757586888	12.3 Volt	600 Pkt	770 Pcnt
1757585628	12.3 Volt	570 Pkt	720 Pcnt
1757584368	12.3 Volt	530 Pkt	700 Pcnt
1757583108	12.3 Volt	510 Pkt	700 Pcnt
1757581848	12.3 Volt	470 Pkt	660 Pcnt
1757580588	12.3 Volt	410 Pkt	640 Pcnt
1757579328	12.3 Volt	440 Pkt	650 Pcnt
1757578068	12.3 Volt	460 Pkt	680 Pcnt
1757576808	12.3 Volt	500 Pkt	720 Pcnt
1757575548	12.3 Volt	470 Pkt	680 Pcnt
1757574288	12.3 Volt	430 Pkt	600 Pcnt
1757573029	12.3 Volt	430 Pkt	560 Pcnt
1757571768	12.3 Volt	410 Pkt	550 Pcnt
1757570509	12.3 Volt	380 Pkt	540 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Rx10m: 0, 10, 0

Eff1h: 0, 10, 0

EffTo: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)