YD1OCG-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD1OCG-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU_Temp*	CPU_Load*	CPU_Freq*	RAM_Free*	Drive_Temp*
1789940425	44 C	29 %	480 MHz	20 %	84 C
1789940173	44 C	2 %	479 MHz	20 %	84 C
1789939929	44 C	2 %	479 MHz	20 %	84 C
1789939649	44 C	5 %	480 MHz	19 %	84 C
1789939369	44 C	5 %	480 MHz	20 %	84 C
1789939114	44 C	31 %	480 MHz	21 %	84 C
1789938864	44 C	30 %	480 MHz	21 %	84 C
1789938599	44 C	34 %	480 MHz	21 %	84 C
1789938349	44 C	4 %	480 MHz	21 %	84 C
1789938109	44 C	32 %	480 MHz	21 %	84 C
1789937800	44 C	4 %	480 MHz	22 %	84 C
1789937560	44 C	4 %	480 MHz	22 %	84 C
1789937305	44 C	31 %	480 MHz	22 %	84 C
1789937050	44 C	2 %	480 MHz	22 %	84 C
1789936785	44 C	31 %	480 MHz	22 %	84 C
1789936495	44 C	4 %	479 MHz	22 %	84 C
1789936255	44 C	30 %	480 MHz	22 %	84 C
1789935955	44 C	4 %	480 MHz	23 %	84 C
1789935655	44 C	37 %	480 MHz	22 %	84 C
1789935370	44 C	30 %	480 MHz	22 %	84 C
1789935075	44 C	31 %	480 MHz	24 %	84 C
1789934791	44 C	2 %	480 MHz	24 %	84 C
1789934521	44 C	4 %	479 MHz	24 %	84 C
1789934251	44 C	5 %	479 MHz	24 %	83 C
1789933976	44 C	5 %	480 MHz	24 %	83 C

*Used Equation Coefficients:

CPU_Temp: 0, 1, 0

CPU_Load: 0, 1, 0

CPU_Freq: 0, 1, 0

RAM_Free: 0, 1, 0

Drive_Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)