E27FGR-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27FGR-9. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Eff1h*
1761398379	14.3 Volt	60 Pkt	81 Pcnt
1761396578	12.88 Volt	0 Pkt	0 Pcnt
1761395677	12.88 Volt	0 Pkt	0 Pcnt
1761394786	12.96 Volt	0 Pkt	100 Pcnt
1761392073	13.04 Volt	90 Pkt	84 Pcnt
1761391173	13.11 Volt	120 Pkt	84 Pcnt
1761390272	13.75 Volt	140 Pkt	84 Pcnt
1761389371	13.04 Volt	150 Pkt	85 Pcnt
1761388473	14.06 Volt	130 Pkt	86 Pcnt
1761387569	13.04 Volt	90 Pkt	86 Pcnt
1761386668	14.22 Volt	40 Pkt	84 Pcnt
1761385767	12.64 Volt	0 Pkt	100 Pcnt
1761384866	12.64 Volt	0 Pkt	100 Pcnt
1761383064	12.64 Volt	0 Pkt	100 Pcnt
1761382164	12.64 Volt	0 Pkt	100 Pcnt
1761381278	12.64 Volt	0 Pkt	100 Pcnt
1761380372	12.64 Volt	0 Pkt	100 Pcnt
1761379461	12.64 Volt	0 Pkt	100 Pcnt
1761378560	12.64 Volt	0 Pkt	100 Pcnt
1761377659	12.64 Volt	0 Pkt	100 Pcnt
1761376758	12.64 Volt	0 Pkt	100 Pcnt
1761375860	12.64 Volt	0 Pkt	100 Pcnt
1761374957	12.64 Volt	0 Pkt	100 Pcnt
1761373155	12.64 Volt	0 Pkt	0 Pcnt
1761372255	12.64 Volt	0 Pkt	0 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)