DM0DOS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DM0DOS-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Vin*	Temp*
1788567336	50 Pkt	12.38 Volt	15.5 C
1788566736	50 Pkt	12.38 Volt	15.5 C
1788566136	50 Pkt	12.38 Volt	15.5 C
1788565536	50 Pkt	12.38 Volt	15.5 C
1788564936	50 Pkt	12.38 Volt	15.5 C
1788564336	50 Pkt	12.38 Volt	15.5 C
1788563736	50 Pkt	12.38 Volt	15.5 C
1788563136	50 Pkt	12.38 Volt	16 C
1788562536	50 Pkt	12.38 Volt	16 C
1788561936	50 Pkt	12.38 Volt	16 C
1788561336	50 Pkt	12.38 Volt	16 C
1788560736	40 Pkt	12.38 Volt	16 C
1788560136	50 Pkt	12.38 Volt	16 C
1788559536	60 Pkt	12.38 Volt	16.5 C
1788558936	70 Pkt	12.38 Volt	16.5 C
1788558336	70 Pkt	12.38 Volt	16.5 C
1788557736	70 Pkt	12.38 Volt	16.5 C
1788557136	80 Pkt	12.38 Volt	16.5 C
1788556536	80 Pkt	12.38 Volt	16.5 C
1788555936	70 Pkt	12.38 Volt	16.5 C
1788555336	60 Pkt	12.38 Volt	16.5 C
1788554737	60 Pkt	12.38 Volt	17 C
1788554136	60 Pkt	12.38 Volt	17 C
1788553536	50 Pkt	12.38 Volt	17 C
1788552936	60 Pkt	12.38 Volt	17 C

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Value4: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)