K3TOW-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K3TOW-13. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1753522188	16.28 Volt	35 Pkt	99 Pcnt	255 Deg
1753518588	16.28 Volt	33 Pkt	99 Pcnt	255 Deg
1753514991	16.2 Volt	31 Pkt	98 Pcnt	255 Deg
1753511388	16.35 Volt	30 Pkt	99 Pcnt	255 Deg
1753507788	16.13 Volt	30 Pkt	99 Pcnt	255 Deg
1753504189	15.98 Volt	30 Pkt	99 Pcnt	255 Deg
1753500589	16.05 Volt	28 Pkt	96 Pcnt	255 Deg
1753496989	16.13 Volt	27 Pkt	99 Pcnt	255 Deg
1753493389	16.13 Volt	28 Pkt	98 Pcnt	255 Deg
1753489789	16.2 Volt	30 Pkt	100 Pcnt	255 Deg
1753486190	16.05 Volt	28 Pkt	99 Pcnt	255 Deg
1753482590	16.05 Volt	28 Pkt	95 Pcnt	255 Deg
1753478990	16.05 Volt	25 Pkt	98 Pcnt	255 Deg
1753475390	15.98 Volt	24 Pkt	98 Pcnt	255 Deg
1753471790	15.9 Volt	25 Pkt	97 Pcnt	255 Deg
1753464591	15.75 Volt	23 Pkt	97 Pcnt	255 Deg
1753457391	15.6 Volt	23 Pkt	96 Pcnt	255 Deg
1753453791	15.98 Volt	26 Pkt	98 Pcnt	255 Deg
1753450191	16.05 Volt	29 Pkt	98 Pcnt	255 Deg
1753446592	15.98 Volt	30 Pkt	99 Pcnt	255 Deg
1753442992	16.13 Volt	25 Pkt	99 Pcnt	255 Deg
1753435792	16.43 Volt	28 Pkt	99 Pcnt	255 Deg
1753432192	16.43 Volt	27 Pkt	98 Pcnt	255 Deg
1753428593	16.35 Volt	26 Pkt	99 Pcnt	255 Deg
1753424993	16.2 Volt	31 Pkt	99 Pcnt	255 Deg

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)