This is the latest recevied telemetry packets stored in our database for station/object OE3WAS-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Press*
Temp.in*
Hum*
eCO2*
Temp.out*
1753973286
985 hPa
27.7 C deg
41 %
692 ppm
24.3 C deg
1753971486
985.2 hPa
27.6 C deg
41.5 %
798 ppm
24.2 C deg
1753969686
985.3 hPa
27.7 C deg
41.7 %
706 ppm
24.3 C deg
1753967885
985.5 hPa
27.7 C deg
42.2 %
650 ppm
24.2 C deg
1753962484
986.4 hPa
27.8 C deg
45.3 %
462 ppm
24.6 C deg
1753955282
987.3 hPa
27.5 C deg
46.3 %
409 ppm
24.6 C deg
1753953482
987.5 hPa
26.9 C deg
48 %
416 ppm
24.4 C deg
1753951682
987.6 hPa
24.9 C deg
54.4 %
400 ppm
23.8 C deg
1753271282
984.3 hPa
27.6 C deg
49.3 %
408 ppm
24.7 C deg
1753269482
984.7 hPa
27.4 C deg
49.6 %
415 ppm
24.6 C deg
1753267681
984.9 hPa
27.6 C deg
50.1 %
411 ppm
24.4 C deg
1753266295
985.1 hPa
27 C deg
52.1 %
400 ppm
24.1 C deg
1753265111
985.3 hPa
25.5 C deg
56.6 %
400 ppm
23.8 C deg
1753264968
985.3 hPa
25 C deg
58.5 %
400 ppm
23.8 C deg
*Used Equation Coefficients:
Press: 0, 1, 0
Temp.in: 0, 1, 0
Hum: 0, 1, 0
eCO2: 0, 1, 0
Temp.out: 0, 1, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)