IR1ZVR-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IR1ZVR-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxPkt*	TxPkt*
1757584283	27 Pkt/10m	20 Pkt/10m
1757583079	22 Pkt/10m	20 Pkt/10m
1757581875	29 Pkt/10m	25 Pkt/10m
1757580671	18 Pkt/10m	16 Pkt/10m
1757579466	0 Pkt/10m	0 Pkt/10m
1757579247	0 Pkt/10m	0 Pkt/10m
1757579100	28 Pkt/10m	24 Pkt/10m
1757577895	34 Pkt/10m	31 Pkt/10m
1757576691	22 Pkt/10m	19 Pkt/10m
1757575487	30 Pkt/10m	27 Pkt/10m
1757574283	29 Pkt/10m	27 Pkt/10m
1757573083	9 Pkt/10m	1 Pkt/10m
1757572500	0 Pkt/10m	0 Pkt/10m
1757571673	21 Pkt/10m	1 Pkt/10m
1757570469	29 Pkt/10m	0 Pkt/10m
1757569265	13 Pkt/10m	0 Pkt/10m
1757568212	26 Pkt/10m	0 Pkt/10m
1757567008	22 Pkt/10m	0 Pkt/10m
1757565804	20 Pkt/10m	2 Pkt/10m
1757564601	19 Pkt/10m	2 Pkt/10m
1757563397	19 Pkt/10m	1 Pkt/10m
1757562193	20 Pkt/10m	1 Pkt/10m
1757560989	23 Pkt/10m	2 Pkt/10m
1757559785	21 Pkt/10m	2 Pkt/10m
1757558581	20 Pkt/10m	4 Pkt/10m

*Used Equation Coefficients:

RxPkt: 0, 1, 0

TxPkt: 0, 1, 0

Batt: 0, 0.0196, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)