DB0DOL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0DOL-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1788672598	25.6 C deg	32.6 %	0 C deg
1788672598	25.6 C deg	32.6 %	0 C deg
1788670781	25.7 C deg	32.7 %	0 C deg
1788670781	25.7 C deg	32.7 %	0 C deg
1788669219	25.6 C deg	32.8 %	0 C deg
1788669219	25.6 C deg	32.8 %	0 C deg
1788667598	25.7 C deg	32.7 %	0 C deg
1788667423	25.7 C deg	32.7 %	0 C deg
1788665503	25.7 C deg	32.3 %	0 C deg
1788665425	25.7 C deg	32.3 %	0 C deg
1788663526	26 C deg	32.4 %	0 C deg
1788661783	25.9 C deg	32.2 %	0 C deg
1788661783	25.9 C deg	32.2 %	0 C deg
1788659944	26.1 C deg	32.2 %	0 C deg
1788659944	26.1 C deg	32.2 %	0 C deg
1788658076	26.1 C deg	32.5 %	0 C deg
1788658076	26.1 C deg	32.5 %	0 C deg
1788656351	26.4 C deg	32.4 %	0 C deg
1788656351	26.4 C deg	32.4 %	0 C deg
1788654440	26.6 C deg	32.4 %	0 C deg
1788654440	26.6 C deg	32.4 %	0 C deg
1788652638	26.8 C deg	32.3 %	0 C deg
1788650872	27.1 C deg	32.3 %	0 C deg
1788650872	27.1 C deg	32.3 %	0 C deg
1788649123	27.3 C deg	32.2 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)