OM0OPC-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OM0OPC-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	DgS*
1785287802	13.95 Volt	100 Pcnt	0.08 Pcnt
1785287202	13.95 Volt	100 Pcnt	0.08 Pcnt
1785286602	13.95 Volt	100 Pcnt	0.08 Pcnt
1785286003	13.95 Volt	100 Pcnt	0.08 Pcnt
1785285402	13.95 Volt	100 Pcnt	0.08 Pcnt
1785284802	13.95 Volt	100 Pcnt	0.08 Pcnt
1785284203	13.95 Volt	100 Pcnt	0.08 Pcnt
1785283603	13.95 Volt	100 Pcnt	0.08 Pcnt
1785283003	13.95 Volt	100 Pcnt	0.08 Pcnt
1785282403	13.95 Volt	100 Pcnt	0.08 Pcnt
1785281803	13.95 Volt	100 Pcnt	0.08 Pcnt
1785281203	13.95 Volt	100 Pcnt	0.08 Pcnt
1785280603	13.95 Volt	100 Pcnt	0.08 Pcnt
1785280003	13.95 Volt	100 Pcnt	0.08 Pcnt
1785279403	13.95 Volt	100 Pcnt	0.08 Pcnt
1785278803	13.95 Volt	100 Pcnt	0.08 Pcnt
1785278203	13.95 Volt	100 Pcnt	0.08 Pcnt
1785277603	13.95 Volt	100 Pcnt	0.08 Pcnt
1785277003	13.95 Volt	100 Pcnt	0.08 Pcnt
1785276403	13.95 Volt	100 Pcnt	0.08 Pcnt
1785275803	13.95 Volt	100 Pcnt	0.08 Pcnt
1785275203	13.95 Volt	100 Pcnt	0.08 Pcnt
1785274603	13.95 Volt	100 Pcnt	0.08 Pcnt
1785274003	13.95 Volt	100 Pcnt	0.08 Pcnt
1785273403	13.95 Volt	100 Pcnt	0.08 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

DgS: 0, 0.001, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)