This is the latest recevied telemetry packets stored in our database for station/object SHLBTP. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Rx1h*
Dg1h*
Eff1h*
A5*
1789945678
14.3 Volt
280 Pkt
70 Pkt
59 Pcnt
0 None
1789938478
14.3 Volt
380 Pkt
80 Pkt
67 Pcnt
0 None
1789924079
14.3 Volt
200 Pkt
60 Pkt
49 Pcnt
0 None
1789916879
14.3 Volt
290 Pkt
60 Pkt
50 Pcnt
0 None
1789873681
14.3 Volt
170 Pkt
10 Pkt
58 Pcnt
0 None
1789844882
14.3 Volt
170 Pkt
20 Pkt
49 Pcnt
0 None
1789837682
14.3 Volt
190 Pkt
20 Pkt
47 Pcnt
0 None
1789830483
14.3 Volt
290 Pkt
60 Pkt
67 Pcnt
0 None
1789816083
14.3 Volt
180 Pkt
40 Pkt
56 Pcnt
0 None
1789808883
14.22 Volt
220 Pkt
60 Pkt
55 Pcnt
0 None
1789801684
14.3 Volt
220 Pkt
50 Pkt
51 Pcnt
0 None
1789780084
14.22 Volt
250 Pkt
80 Pkt
53 Pcnt
0 None
1789765686
14.22 Volt
220 Pkt
70 Pkt
72 Pcnt
0 None
1789758485
14.22 Volt
210 Pkt
50 Pkt
64 Pcnt
0 None
1789751286
14.22 Volt
190 Pkt
60 Pkt
63 Pcnt
0 None
*Used Equation Coefficients:
Vin: 0, 0.079, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
A5: 0, 0, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)