CFWFC Telemetry

This is the latest recevied telemetry packets stored in our database for station/object CFWFC. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*
1789960121	13.68 Volts	36.88 Deg.C
1789960105	13.27 Volts	37.37 Deg.C
1789960077	13.39 Volts	36.88 Deg.C
1789960070	13.33 Volts	36.88 Deg.C
1789960065	13.54 Volts	36.88 Deg.C
1789960038	13.24 Volts	36.39 Deg.C
1789960033	13.3 Volts	36.39 Deg.C
1789960013	13.57 Volts	35.41 Deg.C
1789960008	13.42 Volts	35.41 Deg.C
1789960002	13.33 Volts	35.41 Deg.C
1789959996	13.48 Volts	35.41 Deg.C
1789959991	13.48 Volts	34.92 Deg.C
1789959986	13.36 Volts	35.41 Deg.C
1789959981	13.39 Volts	34.92 Deg.C
1789959975	13.42 Volts	34.92 Deg.C
1789959968	13.3 Volts	35.41 Deg.C
1789959960	13.33 Volts	34.92 Deg.C
1789959954	13.36 Volts	34.92 Deg.C
1789959949	13.39 Volts	34.92 Deg.C
1789959944	13.36 Volts	35.9 Deg.C
1789959937	13.33 Volts	34.92 Deg.C
1789959929	13.33 Volts	34.43 Deg.C
1789959903	13.42 Volts	34.43 Deg.C
1789959843	13.42 Volts	34.92 Deg.C
1789959781	13.39 Volts	34.92 Deg.C

*Used Equation Coefficients:

Value1: 0, 0.0293, 0

Value2: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)