KB4MDD-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KB4MDD-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery*	Temp*
1787533660	12.28 Volts	97.62 Deg.F
1787533660	12.31 Volts	97.62 Deg.F
1787533627	12.28 Volts	97.62 Deg.F
1787533621	12.31 Volts	97.62 Deg.F
1787533505	12.42 Volts	99.37 Deg.F
1787532905	13.48 Volts	94.1 Deg.F
1787530038	12.8 Volts	101.13 Deg.F
1787529549	12.28 Volts	103.77 Deg.F
1787529539	12.25 Volts	103.77 Deg.F
1787529535	12.22 Volts	103.77 Deg.F
1787529516	12.22 Volts	103.77 Deg.F
1787529506	12.28 Volts	103.77 Deg.F
1787529399	13.42 Volts	102.01 Deg.F
1787529388	13.54 Volts	101.13 Deg.F
1787529342	13.6 Volts	101.13 Deg.F
1787525626	13.1 Volts	106.41 Deg.F
1787525575	13.39 Volts	105.53 Deg.F
1787525516	13.51 Volts	104.65 Deg.F
1787510453	12.25 Volts	100.25 Deg.F
1787510446	12.28 Volts	100.25 Deg.F
1787510331	12.31 Volts	100.25 Deg.F
1787510309	12.28 Volts	100.25 Deg.F
1787510296	12.28 Volts	100.25 Deg.F
1787510234	12.25 Volts	100.25 Deg.F
1787509968	12.31 Volts	100.25 Deg.F

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.879, -459.67

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)