ED2YAA-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED2YAA-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1761526340	12.3 Volt	100 Pcnt	42.5 C
1761526040	12.3 Volt	100 Pcnt	42.5 C
1761525740	12.3 Volt	100 Pcnt	42.5 C
1761525440	12.38 Volt	100 Pcnt	42.5 C
1761525140	12.3 Volt	100 Pcnt	42.5 C
1761524840	12.3 Volt	100 Pcnt	42.5 C
1761524540	12.38 Volt	100 Pcnt	42.5 C
1761524240	12.3 Volt	100 Pcnt	42.5 C
1761523940	12.3 Volt	100 Pcnt	42.5 C
1761523640	12.3 Volt	100 Pcnt	42.5 C
1761523340	12.38 Volt	100 Pcnt	42.5 C
1761523040	12.38 Volt	100 Pcnt	42.5 C
1761522740	12.38 Volt	100 Pcnt	42.5 C
1761522440	12.3 Volt	100 Pcnt	42.5 C
1761522140	12.38 Volt	100 Pcnt	42.5 C
1761521840	12.38 Volt	100 Pcnt	43 C
1761521240	12.3 Volt	100 Pcnt	43 C
1761520940	12.3 Volt	100 Pcnt	43 C
1761520640	12.38 Volt	100 Pcnt	43 C
1761520340	12.38 Volt	100 Pcnt	43 C
1761520040	12.38 Volt	100 Pcnt	43 C
1761519740	12.38 Volt	100 Pcnt	43 C
1761519440	12.38 Volt	100 Pcnt	43 C
1761519140	12.38 Volt	100 Pcnt	43 C
1761518840	12.38 Volt	100 Pcnt	43 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)