KK7CXF-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KK7CXF-4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	OutT*	InvertT*	MainSOC*	SecSOC*	BattT*
1765562567	39 DegF	109 DegF	91 S	99 S	12
1765561966	38 DegF	107 DegF	90 S	99 S	12
1765561366	38 DegF	107 DegF	88 S	99 S	11
1765560766	37 DegF	107 DegF	87 S	99 S	11
1765560166	36 DegF	105 DegF	86 S	99 S	11
1765559566	36 DegF	105 DegF	84 S	99 S	11
1765558966	34 DegF	105 DegF	83 S	99 S	11
1765558367	33 DegF	105 DegF	82 S	99 S	11
1765557767	31 DegF	105 DegF	81 S	99 S	11
1765557167	29 DegF	111 DegF	80 S	99 S	11
1765556567	27 DegF	113 DegF	79 S	99 S	11
1765555966	25 DegF	109 DegF	79 S	99 S	11
1765555366	24 DegF	105 DegF	78 S	99 S	11
1765554766	22 DegF	100 DegF	78 S	99 S	11
1765554166	20 DegF	95 DegF	78 S	99 S	11
1765553566	18 DegF	89 DegF	78 S	99 S	11
1765552967	18 DegF	84 DegF	78 S	99 S	11
1765552367	18 DegF	84 DegF	78 S	99 S	11
1765551767	18 DegF	84 DegF	78 S	99 S	11
1765551167	18 DegF	84 DegF	78 S	99 S	11
1765549966	19 DegF	84 DegF	79 S	99 S	11
1765549366	19 DegF	84 DegF	79 S	99 S	11
1765548766	19 DegF	86 DegF	79 S	99 S	11
1765548166	20 DegF	84 DegF	79 S	99 S	11
1765547567	20 DegF	84 DegF	80 S	99 S	11

*Used Equation Coefficients:

OutT: 0, 1, 0

InvertT: 0, 1, 0

MainSOC: 0, 1, 0

SecSOC: 0, 1, 0

BattT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)