SR2LMU-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR2LMU-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1776688840	0 Count	45 Count	3.92 VDC
1776685240	0 Count	36 Count	3.92 VDC
1776681640	0 Count	13 Count	3.92 VDC
1776678040	2 Count	1003 Count	3.91 VDC
1776674440	2 Count	997 Count	3.91 VDC
1776670840	2 Count	991 Count	3.9 VDC
1776667240	2 Count	985 Count	3.91 VDC
1776663639	2 Count	979 Count	3.9 VDC
1776660039	2 Count	972 Count	3.91 VDC
1776656439	2 Count	966 Count	3.91 VDC
1776652839	2 Count	960 Count	3.92 VDC
1776649239	2 Count	948 Count	3.92 VDC
1776645639	2 Count	942 Count	3.92 VDC
1776642038	2 Count	936 Count	3.92 VDC
1776638438	2 Count	930 Count	3.91 VDC
1776634838	2 Count	924 Count	3.91 VDC
1776631238	2 Count	918 Count	3.92 VDC
1776627638	2 Count	912 Count	3.91 VDC
1776624038	2 Count	900 Count	3.92 VDC
1776620438	2 Count	894 Count	3.91 VDC
1776616837	2 Count	880 Count	3.92 VDC
1776613237	2 Count	864 Count	3.91 VDC
1776609637	2 Count	845 Count	3.92 VDC
1776606037	2 Count	810 Count	3.92 VDC
1776602437	2 Count	802 Count	3.92 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)