SP6RJ-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP6RJ-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1772728179	26 Count	1 Count	4.33 VDC
1772727578	16 Count	0 Count	4.24 VDC
1772726978	9 Count	0 Count	4.22 VDC
1772726377	1004 Count	26 Count	4.31 VDC
1772725777	996 Count	26 Count	4.29 VDC
1772725214	986 Count	26 Count	4.29 VDC
1772724576	977 Count	25 Count	4.31 VDC
1772723975	967 Count	25 Count	4.28 VDC
1772723375	958 Count	25 Count	4.25 VDC
1772722774	947 Count	24 Count	4.24 VDC
1772722174	937 Count	24 Count	4.23 VDC
1772721574	929 Count	24 Count	4.23 VDC
1772720974	921 Count	23 Count	4.33 VDC
1772720373	913 Count	23 Count	4.33 VDC
1772719772	905 Count	23 Count	4.26 VDC
1772719171	894 Count	22 Count	4.31 VDC
1772718571	883 Count	22 Count	4.24 VDC
1772717371	865 Count	14 Count	4.26 VDC
1772716770	858 Count	14 Count	4.31 VDC
1772716170	848 Count	14 Count	4.34 VDC
1772715571	838 Count	14 Count	4.31 VDC
1772714970	828 Count	14 Count	4.32 VDC
1772714388	819 Count	14 Count	4.22 VDC
1772713769	810 Count	14 Count	4.23 VDC
1772713169	804 Count	14 Count	4.33 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)