EA2URD-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object EA2URD-2. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1784688641	14.1 Volt	130 Pkt	84 Pcnt
1784686959	14.1 Volt	130 Pkt	80 Pcnt
1784685277	14.1 Volt	100 Pkt	76 Pcnt
1784683596	14.1 Volt	100 Pkt	77 Pcnt
1784681914	14.03 Volt	100 Pkt	74 Pcnt
1784680233	14.03 Volt	100 Pkt	75 Pcnt
1784676869	14.1 Volt	100 Pkt	61 Pcnt
1784675188	14.1 Volt	110 Pkt	65 Pcnt
1784673506	14.03 Volt	130 Pkt	78 Pcnt
1784671826	14.1 Volt	130 Pkt	77 Pcnt
1784670143	14.03 Volt	100 Pkt	81 Pcnt
1784666780	14.1 Volt	120 Pkt	66 Pcnt
1784665098	14.03 Volt	190 Pkt	74 Pcnt
1784663417	14.03 Volt	230 Pkt	88 Pcnt
1784661735	14.03 Volt	210 Pkt	84 Pcnt
1784660053	14.03 Volt	190 Pkt	84 Pcnt
1784658372	14.03 Volt	240 Pkt	93 Pcnt
1784656690	14.03 Volt	350 Pkt	99 Pcnt
1784655009	14.1 Volt	310 Pkt	99 Pcnt
1784653328	14.03 Volt	210 Pkt	97 Pcnt
1784649964	14.1 Volt	190 Pkt	94 Pcnt
1784648282	14.03 Volt	110 Pkt	86 Pcnt
1784646606	14.03 Volt	60 Pkt	85 Pcnt
1784644919	14.03 Volt	70 Pkt	94 Pcnt
1784639874	14.1 Volt	70 Pkt	94 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)