ED2ZAD-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED2ZAD-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1753819822	13.2 Volt	100 Pcnt	26.5 C
1753818922	13.2 Volt	100 Pcnt	26.5 C
1753818022	13.2 Volt	100 Pcnt	26.5 C
1753817122	13.2 Volt	100 Pcnt	27 C
1753816222	13.2 Volt	100 Pcnt	27.5 C
1753815322	13.2 Volt	100 Pcnt	27 C
1753814422	13.13 Volt	100 Pcnt	27 C
1753813522	13.2 Volt	100 Pcnt	27 C
1753812622	13.2 Volt	100 Pcnt	27 C
1753811749	13.2 Volt	100 Pcnt	27 C
1753810822	13.2 Volt	100 Pcnt	27 C
1753809923	13.13 Volt	100 Pcnt	27 C
1753809023	13.2 Volt	100 Pcnt	26.5 C
1753808123	13.2 Volt	100 Pcnt	26.5 C
1753807223	13.2 Volt	100 Pcnt	26.5 C
1753806358	13.13 Volt	100 Pcnt	26 C
1753805423	13.2 Volt	100 Pcnt	26.5 C
1753804523	13.13 Volt	100 Pcnt	26 C
1753803623	13.2 Volt	100 Pcnt	25.5 C
1753802723	13.2 Volt	100 Pcnt	25.5 C
1753801823	13.2 Volt	100 Pcnt	25.5 C
1753800923	13.2 Volt	100 Pcnt	25.5 C
1753800023	13.2 Volt	100 Pcnt	25 C
1753799123	13.2 Volt	100 Pcnt	25.5 C
1753798223	13.2 Volt	100 Pcnt	25 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)