W3NEP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W3NEP-1. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1772953179	13.28 Volt	240 Pkt	130 Pkt	76 Pcnt
1772952276	13.28 Volt	240 Pkt	130 Pkt	79 Pcnt
1772951376	13.28 Volt	220 Pkt	120 Pkt	77 Pcnt
1772950477	13.2 Volt	220 Pkt	130 Pkt	77 Pcnt
1772949576	13.28 Volt	250 Pkt	150 Pkt	77 Pcnt
1772948676	13.2 Volt	250 Pkt	150 Pkt	75 Pcnt
1772947778	13.28 Volt	260 Pkt	160 Pkt	76 Pcnt
1772945977	13.28 Volt	190 Pkt	100 Pkt	76 Pcnt
1772942377	13.28 Volt	160 Pkt	80 Pkt	82 Pcnt
1772941477	13.28 Volt	150 Pkt	70 Pkt	77 Pcnt
1772924378	12.98 Volt	250 Pkt	110 Pkt	73 Pcnt
1772921678	13.13 Volt	270 Pkt	130 Pkt	73 Pcnt
1772920778	13.05 Volt	260 Pkt	120 Pkt	69 Pcnt
1772895580	13.35 Volt	240 Pkt	130 Pkt	75 Pcnt
1772891080	13.28 Volt	260 Pkt	140 Pkt	74 Pcnt
1772890180	13.35 Volt	260 Pkt	130 Pkt	75 Pcnt
1772889289	13.35 Volt	250 Pkt	130 Pkt	75 Pcnt
1772888380	13.35 Volt	230 Pkt	120 Pkt	73 Pcnt
1772887480	13.2 Volt	230 Pkt	120 Pkt	74 Pcnt
1772886580	13.35 Volt	250 Pkt	120 Pkt	75 Pcnt
1772885680	13.35 Volt	240 Pkt	120 Pkt	76 Pcnt
1772884780	13.2 Volt	270 Pkt	130 Pkt	77 Pcnt
1772881180	13.35 Volt	230 Pkt	130 Pkt	75 Pcnt
1772878481	13.35 Volt	230 Pkt	130 Pkt	77 Pcnt
1772877581	13.35 Volt	230 Pkt	120 Pkt	76 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

EffTo: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)