SV1SSF-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SV1SSF-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TX*	RX*	V_Bat*
1761584577	89 Count	741 Count	4.61 VDC
1761582593	88 Count	731 Count	4.61 VDC
1761580609	87 Count	722 Count	4.61 VDC
1761578626	86 Count	713 Count	4.56 VDC
1761576642	85 Count	703 Count	4.62 VDC
1761574658	84 Count	693 Count	4.62 VDC
1761572674	83 Count	685 Count	4.62 VDC
1761570691	82 Count	675 Count	4.62 VDC
1761568707	81 Count	667 Count	4.62 VDC
1761564740	79 Count	646 Count	4.62 VDC
1761560772	77 Count	623 Count	4.62 VDC
1761558789	76 Count	614 Count	4.62 VDC
1761556805	75 Count	602 Count	4.62 VDC
1761555701	70 Count	597 Count	4.62 VDC
1761553719	69 Count	587 Count	4.58 VDC
1761551734	68 Count	578 Count	4.58 VDC
1761549750	67 Count	569 Count	4.61 VDC
1761547767	66 Count	562 Count	4.61 VDC
1761545783	65 Count	554 Count	4.6 VDC
1761543799	63 Count	544 Count	4.6 VDC
1761541815	62 Count	534 Count	4.54 VDC
1761539831	61 Count	524 Count	4.6 VDC
1761537848	60 Count	512 Count	4.6 VDC
1761535866	59 Count	501 Count	4.55 VDC
1761533880	58 Count	491 Count	4.59 VDC

*Used Equation Coefficients:

TX: 0, 1, 0

RX: 0, 1, 0

Digi: 0, 1, 0

V_Bat: 0, 0.01, 0

V_Ext: 0, 0.02, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)