KZ4BN-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KZ4BN-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*
1773139563	13.73 Volt	20 Pkt	45 Pcnt
1773139562	13.73 Volt	20 Pkt	45 Pcnt
1773139262	13.73 Volt	20 Pkt	47 Pcnt
1773138962	13.8 Volt	20 Pkt	45 Pcnt
1773138362	13.65 Volt	20 Pkt	42 Pcnt
1773138062	13.65 Volt	20 Pkt	40 Pcnt
1773137762	13.73 Volt	20 Pkt	41 Pcnt
1773137462	13.65 Volt	20 Pkt	43 Pcnt
1773137162	13.73 Volt	20 Pkt	40 Pcnt
1773136862	13.73 Volt	10 Pkt	35 Pcnt
1773136562	13.8 Volt	10 Pkt	29 Pcnt
1773136262	13.73 Volt	10 Pkt	28 Pcnt
1773135963	13.8 Volt	10 Pkt	29 Pcnt
1773135962	13.8 Volt	10 Pkt	29 Pcnt
1773135662	13.8 Volt	10 Pkt	31 Pcnt
1773135362	13.8 Volt	10 Pkt	34 Pcnt
1773135062	13.88 Volt	10 Pkt	32 Pcnt
1773134763	13.88 Volt	10 Pkt	30 Pcnt
1773134762	13.88 Volt	10 Pkt	30 Pcnt
1773134462	13.8 Volt	10 Pkt	35 Pcnt
1773134168	13.8 Volt	10 Pkt	38 Pcnt
1773134162	13.8 Volt	10 Pkt	38 Pcnt
1773133862	13.8 Volt	10 Pkt	44 Pcnt
1773133562	13.8 Volt	20 Pkt	46 Pcnt
1773133262	13.8 Volt	20 Pkt	52 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)