This is the latest recevied telemetry packets stored in our database for station/object S55YZA-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
Vin*
Rx1h*
Dg1h*
Eff1h*
Temp*
1784674396
12.88 Volt
970 Pkt
240 Pkt
61 Pcnt
18.5 C
1784672297
13.27 Volt
950 Pkt
230 Pkt
59 Pcnt
19 C
1784670194
13.19 Volt
880 Pkt
220 Pkt
58 Pcnt
19 C
1784668093
13.19 Volt
920 Pkt
210 Pkt
63 Pcnt
19.5 C
1784665988
13.19 Volt
990 Pkt
240 Pkt
63 Pcnt
19.5 C
1784663886
13.19 Volt
1000 Pkt
240 Pkt
62 Pcnt
20 C
1784661784
13.19 Volt
850 Pkt
190 Pkt
64 Pcnt
20 C
1784659682
13.19 Volt
830 Pkt
190 Pkt
66 Pcnt
20.5 C
1784657580
13.19 Volt
980 Pkt
210 Pkt
66 Pcnt
20 C
1784655477
13.27 Volt
890 Pkt
200 Pkt
69 Pcnt
21 C
1784653375
13.19 Volt
920 Pkt
220 Pkt
69 Pcnt
21 C
1784651273
13.27 Volt
990 Pkt
250 Pkt
65 Pcnt
21 C
1784649175
13.19 Volt
890 Pkt
220 Pkt
66 Pcnt
21.5 C
1784647069
13.19 Volt
900 Pkt
240 Pkt
66 Pcnt
22 C
1784644967
13.27 Volt
930 Pkt
250 Pkt
64 Pcnt
22.5 C
1784642869
13.11 Volt
930 Pkt
250 Pkt
63 Pcnt
23 C
1784640766
13.27 Volt
1010 Pkt
280 Pkt
67 Pcnt
23 C
1784638664
13.27 Volt
1010 Pkt
290 Pkt
69 Pcnt
22.5 C
*Used Equation Coefficients:
Vin: 0, 0.07713, 0
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
Temp: 0, 0.5, -69
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)