HS5TQA Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RF->INET*	AllCount*	AllDrop*
1776856528	14 Pkts	22 Pkts	0 Pkts
1776855928	8 Pkts	16 Pkts	2 Pkts
1776855329	9 Pkts	19 Pkts	2 Pkts
1776854729	12 Pkts	19 Pkts	2 Pkts
1776854129	12 Pkts	24 Pkts	1 Pkts
1776853529	8 Pkts	16 Pkts	2 Pkts
1776852929	16 Pkts	26 Pkts	3 Pkts
1776852329	11 Pkts	19 Pkts	1 Pkts
1776851729	11 Pkts	20 Pkts	0 Pkts
1776851129	6 Pkts	11 Pkts	0 Pkts
1776850529	0 Pkts	9 Pkts	0 Pkts
1776849929	0 Pkts	5 Pkts	0 Pkts
1776849329	0 Pkts	9 Pkts	0 Pkts
1776848729	10 Pkts	16 Pkts	0 Pkts
1776848129	32 Pkts	46 Pkts	5 Pkts
1776847529	7 Pkts	14 Pkts	1 Pkts
1776846929	13 Pkts	23 Pkts	1 Pkts
1776846329	7 Pkts	15 Pkts	2 Pkts
1776845729	12 Pkts	22 Pkts	4 Pkts
1776845129	19 Pkts	29 Pkts	4 Pkts
1776844529	7 Pkts	18 Pkts	8 Pkts
1776843929	13 Pkts	22 Pkts	1 Pkts
1776843329	15 Pkts	24 Pkts	2 Pkts
1776842729	12 Pkts	20 Pkts	1 Pkts
1776842129	15 Pkts	23 Pkts	1 Pkts

*Used Equation Coefficients:

RF->INET: 0, 1, 0

INET->RF: 0, 1, 0

Repeater: 0, 1, 0

AllCount: 0, 1, 0

AllDrop: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)