K4KSC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K4KSC-12. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Battery SOC*	Battery Charge Power*	PV Voltage*	PV Power*	Inverter Power*
1766080066	53.9 V	5.9 A	91 %	352 W	40 W
1766079467	54 V	4.7 A	90 %	278 W	40 W
1766078864	54 V	3.9 A	90 %	268 W	41 W
1766078267	54.3 V	11.9 A	89 %	661 W	41 W
1766077663	54 V	6 A	87 %	359 W	42 W
1766077064	54 V	4.8 A	86 %	297 W	41 W
1766076460	53.7 V	4.8 A	85 %	281 W	41 W
1766075860	53.8 V	2.8 A	85 %	218 W	41 W
1766075263	53.6 V	1 A	84 %	135 W	39 W
1766074656	54 V	5.8 A	84 %	248 W	40 W
1766074058	53.8 V	3.3 A	83 %	251 W	40 W
1766072255	54.1 V	8.3 A	80 %	452 W	41 W
1766071660	54 V	8.8 A	79 %	465 W	41 W
1766071065	54 V	8.2 A	77 %	434 W	41 W
1766070480	54 V	8.3 A	76 %	420 W	40 W
1766069867	54 V	9.1 A	75 %	475 W	41 W
1766069266	54 V	7 A	74 %	407 W	41 W
1766068067	53.8 V	2.4 A	73 %	192 W	41 W
1766067454	54 V	5 A	73 %	305 W	41 W
1766066869	53.7 V	4.9 A	72 %	275 W	40 W
1766065670	53.4 V	1.3 A	71 %	123 W	41 W
1766065055	53.4 V	0.5 A	71 %	91 W	40 W
1766064466	53.4 V	2.5 A	71 %	195 W	40 W
1766063863	53.3 V	1.6 A	71 %	130 W	40 W
1766062661	53.2 V	0.1 A	71 %	61 W	41 W

*Used Equation Coefficients:

Battery SOC: 0, 1, 0

Battery Charge Power: 0, 1, 0

PV Voltage: 0, 1, 0

PV Power: 0, 1, 0

Inverter Power: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)