This is the latest recevied telemetry packets stored in our database for station/object EA5IUE-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
Time
TX*
RX*
Digi*
V_Bat*
V_Ext*
1754188813
25 Count
0 Count
0 Count
0 VDC
0 VDC
1754187010
24 Count
0 Count
0 Count
0 VDC
0 VDC
1754185207
23 Count
0 Count
0 Count
0 VDC
0 VDC
1754183445
22 Count
0 Count
0 Count
0 VDC
0 VDC
1754177994
19 Count
0 Count
0 Count
0 VDC
0 VDC
1754176191
18 Count
0 Count
0 Count
0 VDC
0 VDC
1754174388
17 Count
0 Count
0 Count
0 VDC
0 VDC
1754172585
16 Count
0 Count
0 Count
0 VDC
0 VDC
1754170782
15 Count
0 Count
0 Count
0 VDC
0 VDC
1754168979
14 Count
0 Count
0 Count
0 VDC
0 VDC
1754167236
13 Count
0 Count
0 Count
0 VDC
0 VDC
1754165412
12 Count
0 Count
0 Count
0 VDC
0 VDC
1754163609
11 Count
0 Count
0 Count
0 VDC
0 VDC
1754158200
8 Count
0 Count
0 Count
0 VDC
0 VDC
1754156397
7 Count
0 Count
0 Count
0 VDC
0 VDC
1754154594
6 Count
0 Count
0 Count
0 VDC
0 VDC
1754152791
5 Count
0 Count
0 Count
0 VDC
0 VDC
1754150988
4 Count
0 Count
0 Count
0 VDC
0 VDC
1754149184
3 Count
0 Count
0 Count
0 VDC
0 VDC
1754146734
0 Count
0 Count
0 Count
0 VDC
0 VDC
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0). The sent equation coefficients is used in the equation: a * value2 + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)