OE8ADF Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE8ADF. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1787613928	12.9 Volt	0 Pcnt	16 C
1787613927	12.9 Volt	0 Pcnt	16 C
1787613328	12.9 Volt	0 Pcnt	16.5 C
1787612729	12.9 Volt	0 Pcnt	16.5 C
1787612728	12.9 Volt	0 Pcnt	16.5 C
1787612128	12.9 Volt	0 Pcnt	17 C
1787611528	12.9 Volt	0 Pcnt	17 C
1787610928	12.9 Volt	100 Pcnt	17 C
1787610328	12.9 Volt	100 Pcnt	17 C
1787609728	12.9 Volt	100 Pcnt	17 C
1787609128	12.9 Volt	100 Pcnt	17 C
1787607928	12.9 Volt	100 Pcnt	17.5 C
1787606728	12.9 Volt	100 Pcnt	17.5 C
1787606128	12.9 Volt	100 Pcnt	17.5 C
1787605528	12.9 Volt	100 Pcnt	18 C
1787604928	12.9 Volt	100 Pcnt	17.5 C
1787604328	12.9 Volt	100 Pcnt	18 C
1787603728	12.9 Volt	100 Pcnt	18 C
1787603128	12.9 Volt	100 Pcnt	18 C
1787602528	12.9 Volt	100 Pcnt	18 C
1787601928	12.9 Volt	0 Pcnt	18 C
1787601328	12.9 Volt	0 Pcnt	18.5 C
1787600728	12.9 Volt	0 Pcnt	18.5 C
1787600128	12.9 Volt	0 Pcnt	18.5 C
1787599528	12.9 Volt	8 Pcnt	19 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Digi1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)