DG1FBP-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG1FBP-11. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp.in*	Hum*	Temp.out*
1753778269	22.6 C deg	66.4 %	0 C deg
1753778261	22.6 C deg	66.4 %	0 C deg
1753776461	22.3 C deg	67.4 %	0 C deg
1753776461	22.3 C deg	67.4 %	0 C deg
1753774661	21.9 C deg	67.4 %	0 C deg
1753774661	21.9 C deg	67.4 %	0 C deg
1753772861	20.9 C deg	70.3 %	0 C deg
1753772861	20.9 C deg	70.3 %	0 C deg
1753771061	21.3 C deg	69.8 %	0 C deg
1753771061	21.3 C deg	69.8 %	0 C deg
1753769261	21.2 C deg	70.5 %	0 C deg
1753769261	21.2 C deg	70.5 %	0 C deg
1753765660	21.1 C deg	70.2 %	0 C deg
1753765660	21.1 C deg	70.2 %	0 C deg
1753763860	21 C deg	70.2 %	0 C deg
1753763860	21 C deg	70.2 %	0 C deg
1753762060	21.1 C deg	69.9 %	0 C deg
1753762060	21.1 C deg	69.9 %	0 C deg
1753760260	21.2 C deg	70.1 %	0 C deg
1753760260	21.2 C deg	70.1 %	0 C deg
1753758460	21.3 C deg	70.4 %	0 C deg
1753758460	21.3 C deg	70.4 %	0 C deg
1753756660	21.2 C deg	70.5 %	0 C deg
1753756660	21.2 C deg	70.5 %	0 C deg
1753754860	21.4 C deg	70.8 %	0 C deg

*Used Equation Coefficients:

Press: 0, 1, 0

Temp.in: 0, 1, 0

Hum: 0, 1, 0

QNH: 0, 1, 0

Temp.out: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)