DC7OS-L4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DC7OS-L4. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1757624569	13.8 deg C	60.2 %	1010.8 hPa
1757623669	13.8 deg C	59.6 %	1010.6 hPa
1757622769	14 deg C	58.6 %	1010.4 hPa
1757621868	14.3 deg C	57 %	1010.2 hPa
1757621537	14.2 deg C	56.9 %	1010.2 hPa
1757620637	14.4 deg C	55.4 %	1010.1 hPa
1757619737	14.9 deg C	53.3 %	1010 hPa
1757618836	15 deg C	52.2 %	1010 hPa
1757617936	15.3 deg C	51.4 %	1010 hPa
1757617036	15.3 deg C	51.2 %	1009.8 hPa
1757616136	15.5 deg C	50.8 %	1009.7 hPa
1757615236	15.6 deg C	51.2 %	1009.4 hPa
1757614336	15.7 deg C	50.6 %	1009.2 hPa
1757613436	15.9 deg C	49.9 %	1009.1 hPa
1757612536	16 deg C	49.8 %	1009 hPa
1757611636	16.4 deg C	50.7 %	1008.8 hPa
1757610736	16.6 deg C	52.1 %	1008.6 hPa
1757609836	16.7 deg C	51.7 %	1008.4 hPa
1757609506	16.8 deg C	52.2 %	1008.5 hPa
1757608605	16.9 deg C	50.9 %	1008.3 hPa
1757607705	17.7 deg C	44.8 %	1007.9 hPa
1757606805	18.1 deg C	43.4 %	1007.5 hPa
1757605905	18.7 deg C	42.3 %	1007.5 hPa
1757605005	18.8 deg C	41.3 %	1007.5 hPa
1757604105	19.3 deg C	39.7 %	1007.3 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)