BV4HW-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV4HW-3. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1772602846	37.3 C	1 p	41 p	81 p	79 p
1772601644	36.1 C	22 p	42 p	80 p	78 p
1772600445	34.9 C	24 p	27 p	64 p	62 p
1772599258	34.2 C	2 p	3 p	40 p	38 p
1772598045	36.5 C	1 p	2 p	39 p	37 p
1772596845	35.2 C	1 p	13 p	38 p	36 p
1772595644	32.5 C	12 p	27 p	37 p	35 p
1772594445	30.6 C	12 p	27 p	37 p	35 p
1772590845	27.9 C	11 p	12 p	12 p	12 p
1772589646	28.2 C	1 p	1 p	1 p	1 p
1772586045	28.3 C	8 p	14 p	136 p	116 p
1772583645	22 C	8 p	14 p	136 p	116 p
1772582445	13.3 C	8 p	14 p	136 p	116 p
1772526999	32.8 C	10 p	20 p	125 p	113 p
1772525799	29.9 C	10 p	17 p	122 p	110 p
1772516199	35.5 C	7 p	18 p	80 p	72 p
1772512598	35.5 C	6 p	24 p	62 p	54 p
1772511399	33.1 C	6 p	24 p	62 p	54 p
1772510199	32.7 C	6 p	22 p	58 p	50 p
1772509001	31.6 C	6 p	18 p	53 p	45 p
1772501799	30.6 C	7 p	17 p	22 p	17 p
1772500598	30.6 C	9 p	17 p	18 p	14 p
1772498198	27.5 C	6 p	7 p	7 p	5 p
1772496998	24.7 C	1 p	1 p	1 p	93 p
1772495797	16.6 C	1 p	8 p	102 p	93 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)