TSTING-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TSTING-5. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Cur*
1756119201	12.64 Volt	100 Pcnt	1.76 A
1756118602	12.64 Volt	100 Pcnt	1.76 A
1756118302	12.64 Volt	100 Pcnt	1.76 A
1756118002	12.64 Volt	100 Pcnt	1.76 A
1756117702	12.64 Volt	100 Pcnt	1.76 A
1756117402	12.64 Volt	100 Pcnt	1.76 A
1756117102	12.64 Volt	100 Pcnt	1.76 A
1756116802	12.64 Volt	100 Pcnt	1.76 A
1756116502	12.64 Volt	100 Pcnt	1.76 A
1756116202	12.64 Volt	100 Pcnt	1.76 A
1756115902	12.64 Volt	100 Pcnt	1.76 A
1756115608	12.64 Volt	100 Pcnt	1.76 A
1756115302	12.64 Volt	100 Pcnt	1.76 A
1756115002	12.64 Volt	100 Pcnt	1.76 A
1756114402	12.64 Volt	100 Pcnt	1.76 A
1756114102	12.64 Volt	100 Pcnt	1.76 A
1756113802	12.64 Volt	100 Pcnt	1.76 A
1756113511	12.64 Volt	100 Pcnt	1.76 A
1756113202	12.64 Volt	100 Pcnt	1.76 A
1756112902	12.64 Volt	100 Pcnt	1.76 A
1756112302	12.64 Volt	100 Pcnt	1.76 A
1756112002	12.64 Volt	100 Pcnt	1.76 A
1756111702	12.64 Volt	100 Pcnt	1.76 A
1756111402	12.64 Volt	100 Pcnt	1.76 A
1756111102	12.64 Volt	100 Pcnt	1.76 A

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Cur: 0, 0.1953, -24.8031

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)