DL2YCP-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL2YCP-15. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Humi*	Baro*
1780862764	20.7 deg C	54.9 %	1018.5 hPa
1780861864	20.7 deg C	54.8 %	1018.5 hPa
1780860960	20.7 deg C	54.7 %	1018.4 hPa
1780860056	20.7 deg C	54.6 %	1018.4 hPa
1780859157	20.7 deg C	54.5 %	1018.4 hPa
1780858261	20.8 deg C	54.4 %	1018.3 hPa
1780857953	20.8 deg C	54.4 %	1018.4 hPa
1780857055	20.8 deg C	54.4 %	1018.4 hPa
1780856153	20.7 deg C	54.5 %	1018.3 hPa
1780855252	20.7 deg C	54.5 %	1018.3 hPa
1780854351	20.7 deg C	54.5 %	1018.2 hPa
1780853445	20.7 deg C	54.5 %	1018.4 hPa
1780852546	20.7 deg C	54.6 %	1018.5 hPa
1780850744	20.7 deg C	54.7 %	1018.6 hPa
1780849845	20.6 deg C	54.7 %	1018.5 hPa
1780848941	20.6 deg C	54.8 %	1018.6 hPa
1780848041	20.6 deg C	54.9 %	1018.7 hPa
1780847142	20.5 deg C	54.9 %	1018.8 hPa
1780846229	20.5 deg C	55 %	1018.8 hPa
1780845903	20.5 deg C	55 %	1018.8 hPa
1780845002	20.4 deg C	55.1 %	1018.8 hPa
1780844099	20.4 deg C	55.1 %	1018.8 hPa
1780843200	20.3 deg C	55.2 %	1018.9 hPa
1780842300	20.2 deg C	55 %	1018.9 hPa
1780841398	20.2 deg C	55.2 %	1018.9 hPa

*Used Equation Coefficients:

Temp: 0, 0.1, 0

Humi: 0, 0.1, 0

Baro: 0, 0.1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)