LU8SAM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU8SAM-10. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1773266088	39 Pkt	-30 dBm	0.74 V
1773264865	40 Pkt	-31 dBm	1.05 V
1773263643	21 Pkt	-28 dBm	0.74 V
1773262419	34 Pkt	-29 dBm	0.74 V
1773261196	33 Pkt	-28 dBm	0.74 V
1773259973	26 Pkt	-29 dBm	0.76 V
1773258750	32 Pkt	-28 dBm	0.74 V
1773257528	31 Pkt	-30 dBm	0.76 V
1773256305	25 Pkt	-28 dBm	0.76 V
1773255082	25 Pkt	-28 dBm	0.76 V
1773253859	18 Pkt	-28 dBm	0.76 V
1773252636	25 Pkt	-28 dBm	0.76 V
1773251413	18 Pkt	-28 dBm	0.76 V
1773250191	14 Pkt	-28 dBm	0.76 V
1773248968	15 Pkt	-28 dBm	0.76 V
1773247745	12 Pkt	-28 dBm	0.76 V
1773246523	21 Pkt	-27 dBm	0.76 V
1773245299	23 Pkt	-28 dBm	0.76 V
1773244076	15 Pkt	-28 dBm	0.78 V
1773242854	21 Pkt	-28 dBm	0.76 V
1773241632	40 Pkt	-28 dBm	0.76 V
1773240409	26 Pkt	-30 dBm	0.82 V
1773239186	17 Pkt	-28 dBm	0.76 V
1773237963	30 Pkt	-28 dBm	0.76 V
1773236741	26 Pkt	-28 dBm	0.78 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)