KQ6DI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KQ6DI. If no packets are shown the sender has not sent any telemetry packets the latest 10 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU*	PC Board*	Tc*	count*	dBm*
1789963203	39.7	73.4	57.1	573	-36
1789962604	40.2	73.5	56.9	573	-37
1789962003	40.2	73.4	56.7	571	-37
1789961403	39.7	73.3	56.2	567	-36
1789960804	40.2	73.3	55.7	565	-37
1789960203	39.7	73.4	55.3	563	-36
1789959604	40.2	73.3	54.4	558	-34
1789959003	39.7	73.3	53.6	554	-35
1789958403	39.7	73.1	52.6	548	-37
1789957804	39.7	73.1	52.4	546	-37
1789957203	39.2	72.6	50.7	533	-35
1789956604	37.6	71.6	50.7	524	-36
1789956003	38.6	72.1	51	529	-35
1789955404	40.2	73.6	55.8	568	-35
1789954803	39.7	73.4	54.6	561	-35
1789954203	38.6	72.4	52.2	539	-35
1789953604	38.1	72.6	52.3	541	-35
1789953003	40.2	74.1	55.4	570	-35
1789952404	40.8	74.3	56.4	578	-34
1789951803	40.8	74.2	56.2	575	-36
1789951203	40.8	74	56.3	574	-35
1789950604	40.2	73.8	57.3	577	-35
1789950003	38.6	73	54.9	558	-34
1789949404	40.8	74.5	58.8	591	-34
1789948803	40.8	74.4	58.6	589	-35

*Used Equation Coefficients:

CPU: 0, 0.1, 0

PC Board: 0, 0.1, 0

Tc: 0, 0.1, 0

count: 0, 1, 0

dBm: 0, -1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)